Skip to main content

Hacking the Windtubes in the KSA

Ryan Ryan
July 1, 2012
Calculating...
Hacking the Windtubes in the KSA

We brought lots of tools and extra supplies with us to Saudi Arabia so that we could tinker with our activities, make adjustments to the exhibits, and adapt to what we notice in the environment. This week we had the occasion to use our extra supplies to "hack" our wind tubes to improve the visitor experience in our space.

The wind tubes that we brought use vornado fans which have enough power to lift objects up, but have blades that are shaped in a way that spirals the air through the tube. The result was that every constructed object behaved the same way in the tubes; the participants could not see how the changes that they made affected the motion of their flying creations. Because the exhibit didn't support people spending time solving problems and making small tweaks to their designs, it quickly turned into a magnet for little kids to just throw a whole bunch of baskets in the tube and watch them fly out. Entertaining-yes, but tinkering-not quite.

IMG_0105

So Chas and I had the idea to borrow the concept of the wind table that we have been working on back in the San Francisco Tinkering Studio and make a bed of tubes which would hopefully direct the airstream into a more laminar flow.

Saudi Arabia 6/29/12
We started by tightly stuffing straws into derders. In this case, a whole tube would be too tall to fit in the opening and still let people place their creations in the air flow. We guessed that one and a half inch tubes would work well enough, but cutting them down to size proved to be a challenge.

DSC_8474
Adam made a jig to help us cut the tubes and had the idea of taping the ends shut. For cutting, we tried an exacto blade, scissors, and even the saw, all before finding that the hand saw had the best mix of speed and clean cuts.

DSC_8485
Soon we had a bunch of mini straw-filled derders and were ready to glue them into a circle that we could squeeze into the wooden ring that nests in the opening above the fan.

DSC_8490

DSC_8495
We filled in the gaps in between the tubes with more straws and cut them down to size with scissors.

DSC_8499
Chas, Adam, and I brought it out on the floor to test, but it didn't let enough air through and could lift most objects. Luckily I know the oldest trick in the prototyping guidebook.

DSC_8504
...pretend to be clumsy and "accidentally" drop the object, scattering all of the straws that we stuffed into the spaces between the tubes. Of course I meant to do that, because we found that without the straws that I so fortunately spilled all over the floor, more air could get though and objects could float higher in the tube.

DSC_8508
I knew when I tested a dixie cup cut with diagonal scores and it spun beautifully in the wind tube (something that wouldn't happen without the straws) our project would be a success.

DSC_8519
Fatin, one of our Saudi facilitators, also got excited about the results and decided that she wanted to help us make the modification to the other wind tube as well. So Adam showed her our technique and taught her how to use the hand saw and jig and she went to work. She did an awesome job and after a couple of hours we had enough tubes to assemble the second ring for the other wind tube.

Saudi Arabia 7/1/12

The next day, with straws in both tubes, we immediately noticed a change of behavior in the visitors to the space. With the new materials palette that we tried out-- similar to the wind table materials at home (dixie cups, strips of paper, strawberry baskets, and stolen cone cups from the water cooler)-- people could make all kinds of objects that floated beautifully in the tubes. It was more challenging for visitors because not everything worked the way they thought it would or even flew, but those moments gave facilitators chances to ask "what happens if" questions, give suggestions, and work out their own designs alongside people in the space.

With their eye-catching motion and forward-most position in our space, the wind tubes provide an introduction to our whole booth. With this hack, they serve their intended purpose of getting people in the right frame of mind to work with their hands to make things and to notice the delightful results of their experiments.

Saudi Arabia 7/1/12