Yesterday I blogged about Laura's successful attempt at making a sewn circuit at home after visiting the Tinkering Studio, and today I want to share another example of a family building their own Marble Machines board during their holiday vacation.
Takeo wrote to us explaining what a great time his kids had in the Marble Machines area at the museum, so much so that they didn't want to leave. He wanted to build one to keep playing at home, and make it their family's Christmas project together, and needed some help finding the parts. After pointing him toward the PDF guide we've written just for people like him (and you!) and giving him a few extra pointers, he was off on his own. A few days later, he wrote back saying the project was a great success, and included some photos with permission to post them on our blog! He also wrote some pointers and tips for other families that might want to embark in the same project, so here are his suggestions.
Materials
I got it all from Home Depot, but I think you can get it from Lowes or other home improvement/craft stores.
- Pegboards: Two 24 in x 48 in wood panel pegboards with 1/4 in diameter holes. I got two for $12.
- Side boards for support: I got 3 in total with 1 in x 2 in x 8 ft long slender wood slabs ($2 each). I had a guy at Home Depot cut 2 of them into 4ft each, this will be the side vertical support. The other into 3 pieces of 22in each, this will be the horizontal support.
- Stands: I bought 4 wooden corbels ($2 each) from Home Depot to use as a stand. I initially asked if they cold cut a square piece of wood into a diagonal, but they didn't have anyone or a machine to do it. This alternative worked out great!
- Braces to support the above wooden corbel stand. I thought this was needed to firmly support the wooden stand. Two L-shaped braces and two straight braces.
- Marble ball runner rails (PVC molding). To make the many marble ball runner rails, I was lucky enough to get few pieces free from the scrap section of Home Depot, it was a PVC molding that was perfect for the marble runner. If you need to buy it, it was about $4 each for 8ft.
- Wood rods (Dowels rods): I didn't know it was called a dowel, but they sell it at Home Depot. Make sure it fits into the pegboard, I got the 1/4 in diameter and made sure it fits into the holes.
- Wooden clothes pins
- Wood glue: Just get the smallest one, I didn't need much of it.
- Wood Screws: I got the 45 pack just in case. I didn't use much of it, but it was cheap and I didn't know how much I needed when I got started.
In total about $70, but I think I could have done it for $30 next time if I had used cheaper material.
A few tips and suggestions:
Find free scraps at Home Depot or Lowes. Many stores have a left-overs or scrap area that you can look through, just make sure it's clean. Luckily for us, we found few PVC molding pieces that were perfect to use the marble runners.
Measure and cut at the store. Home Depot or Lowes will cut anything for you, just make sure you have it measured. We had the vertical and the horizontal support wood pieces cut at the store.
Call the store before going to make sure the materials are available. I called several Home Depot stores directly for the peg boards before going to make sure they had it in stock.
Tips about making the boards:
Aligning the two boards is difficult, just make sure it's not too far off by sticking few wooden dowels and make sure they align as best as possible, it doesn't have to be perfect.
Cut the wooden dowels in random lengths, as long as they stick out completely through to the other side. If you cut the dowels, the edges will have splinters or will be rough. Use any rough surface around your home to round out the edges of the wooden dowels, no need to spend time sanding the edges. I used my back yard concrete patio area to scrape the edges.
Determine the bottom of the board first, then construct upward. Meaning, align the side vertical support piece at the bottom, then start screwing in from the bottom. This will make it easier since you don't need to align to the top.
Make sure the vertical and horizontal support wood pieces are straight. At 8ft long a piece, some are bent and some are not completely straight. You can test it by laying it out on the floor. This is one material that you want straight because it'll be the supporting structure for the peg boards.
Involve you kids from the start. Even at Home Depot, I had my kids find the materials and ask for help if needed. This made it more of a game, like a scavenger hunt. Also, I had my kids select which piece they want to buy. Again, another tactic I used to get the kids engaged.
It was a lot fun building it. I'm not good with DIY stuff, but this was something we enjoyed as a family in making it, and now enjoying the completed marble run.
Making a Marble Machines board is definitely more involved in terms of time, effort, and materials than most of the other activities on our site, but definitely within the reach of anyone with a little bit of planning and persistence. I especially like Takeo's closing sentence: “I'm not good with DIY stuff, but this was something we enjoyed as a family in making it, and now enjoying the completed marble run.” In other words, you don't need to already be good at this stuff in order to get started, just be willing to tinker with it a bit…