Skip to main content

Jumping Ring

A person using an electrical toy at a table.
DIY Exhibit
Jumping Ring
Electric currents produce magnetic fields to throw an object upward.
Jumping Ring
Electric currents produce magnetic fields to throw an object upward.

We joined forces with Community Science Workshops to design this DIY Exhibit that you can make from everyday objects for your community space. 
 

Materials

A spool of wire. With a hole in the middle. We used about 100 feet of 18 gauge insulated wire. We made sure that the two ends of the wire were sticking out of the spool we purchased. The hole in the spool measured about an inch across. 
Other things to try: Wind a couple hundred turns of insulated wire around a small tube.

Steel or iron rods. Thin ones. A lot of them. Most stainless steel doesn’t work. A single thick rod can be used, but it won’t work as well. We bought landscaping flags from the hardware store.
Other things to try: wire clothes hangers, straightened bailing wire, extra long nails

An aluminum or copper ring. We used an aluminum ring from climbing gear. 
Other things to try: aluminum foil, a thin slice of a copper tube, a thin brass ring

A flat base. 
We used a piece of plywood.

A doorbell transformer.  To limit voltage for safety and match the coil properties.
Be sure to use a 24-volt AC transformer; 36 volts or above can be dangerous. We bought ours online.

A power cord. With a plug, to connect the transformer to a wall outlet.
Be sure to use a three-prong grounded plug for safety.

A momentary switch. It should be rated for at least 10 amps and 125 AC volts. 
Be sure to use a switch that must be pressed and held to be switched on. We removed ours from an old appliance.

We also used a drill, wire strippers, wire nuts, wood screws, washers, glue, and tape.

How to Make It
Warning sign

This activity has the additional potential to generate heat under heavy continuous use. Be watchful for elevated temperatures on the wire spool or metal ring while in use and discontinue use until these surfaces have cooled down.

Attach the spool to the platform. 

We drilled pilot holes in the wood around the edge of the spool and used wood screws and oversized washers as clamps to hold the spool down.

 

Put the rods in the spool.

We stuffed as many rods in the spool’s hole as would fit, leaving as little extra space as possible, and glued them in place. We then taped the rods into a bundle tight enough for the metal ring to pass smoothly over its length.
 

Connect the transformer, switch, and ends of the wire.

 

See diagram for proper wiring.

The transformer connects to the switch and the wire in the spool. 

The switch connects to the transformer and the wire in the spool. 

Be sure to use wire nuts at the connections between wires, leaving no exposed bare wires anywhere.

 

 

Wire the transformer to the power cord.

Check the instructions that came with the transformer to ensure proper wiring.
 

 

Slip the ring down onto the rod bundle. 


 

 

Plug in the power cord and press the switch. 

If you hold the switch on for a long time, the exhibit might get hot.
 

What’s Going On?

What do you notice?  
What do you wonder?  
What do you want to try?

An electric current creates a magnetic field, and a changing magnetic field creates an electric current. This close relationship between electricity and magnetism makes the ring jump. 

When you push the switch, the current that flows through the coiled wire produces magnetic fields. These strengthening fields induce currents in the rods. The rod currents then create more magnetic fields that produce a current in the ring. And that ring current creates yet another magnetic field, one that is repelled by the original magnetic field of the wire. This repulsive force flings the ring upward.

Troubleshooting Tips
  • Be sure to unplug the exhibit before troubleshooting. 
  • If the ring doesn’t jump very high, try a spool with a bigger hole, insert more metal rods, add more turns of wire, or try a ring with a smaller diameter. 
  • A ring that is a seamless loop (not different pieces of material joined together) will work best.  
  • Do not remove the transformer; it provides safety by limiting the voltage.